Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Parts & Accessories

Zipp Tangente Tube Wrench
$7.00
Zipp Speed Weaponry Valve Extender Wrench Set - Two 4 mm and 5 mm combination wrenches - Replacement wrenches required to properly install Zipp integrated valve extenders - Use with Zipp Tangente tubes with aluminum Presta valve and aluminum valve extender
Stan's NoTubes Presta Removeable Valve Core
$2.00
Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.
Whisky Parts Co. Tubeless Rim Tape
$8.00 - $40.00
Whisky’s tubeless rim tape is designed to make setup as easy as possible. Elasticity allows for smooth, even adherence while translucency lets you see where the tape contacts the rim. Different widths available to fit almost any rim.
Problem Solvers Thru-Axle/QR Adaptor
$19.99
Thru-Axle hub adapters allow the use of 100 mm front thru-axle hubs in 100 mm QR forks. -Allows the use of modern thru-axle wheels in forks designed for quick-release compatible hubs -100 mm front hub spacing only -CNC-machined AL-6061
Wheels Manufacturing Inc. CN-R102 Cone
$10.00
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Front 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Cone Diameter: 14.8mm - Dust Seal Diameter: 22mm - Length: 10.6mm - 1 cone per bag COMPATIBLE HUBS: - Tiagra 4400 Front - Shimano Sora HB-3300 Front - Shimano Acera HB-M330 Front - Shimano Nexave HB-T300 Front
Stan's NoTubes Neo Hub Spring and Pawl Kit
$9.00
Replacement springs and pawls. Includes 6 pawls, 6 springs and 1 plastic retaining ring that holds the pawls in place even during disassembly to ensure you're never searching the floor for tiny springs.
Atomlab Torque Nipples
$21.95
- Proprietary 6mm thick (standard is 4mm) 7075 aluminum nipple offering the strength of a brass nipple while saving 20 grams per wheel, plus more pivot range at the spoke hole for reduced stress on spoke - Only for use with Torque nipple specific rims. Sold in bags of 36 nipples - T-20 Torx broach for pre-tensioning, 3mm flats for fine adjustment - See Tools - Wheelbuilding section for Atomlab Torque nipple tools
Stan's NoTubes Neo Replacement Rear Axle
$18.00
Replacement rear axle for Neo and Neo Ultimate hubs. High-precision center-less ground treatment ensures perfect bearing fit.
HALO Replacement Driver, DJD Bush Drive
$95.95
- Replacement driver for Original DJD or DJD-Bush Drive rear hub - Need DJD Original removal tool or DJD Bush Drive removal tool (sold separately)
Spank Oozy/Spike Rear Hub Adaptors
$19.90
Hub Adapters for all Oozy hubs and 2016 Spike hubs.
Stan's NoTubes Neo Conversion Kit
$52.00
Kit allows you to convert your Neo or Neo Ultimate hub. The thru-axle to QR kit includes two SealLock end caps and Stan's aluminum quick-release skewer. SealLock end caps feature a low-friction U-cup seal that snaps into place and stays secure even when your wheel is removed from your bike. The QR/thru-axle to bolt-on kit includes end caps, threaded axle, bolts and washers. Bolt-on axles are recommended to prevent slipping and wheel misalignment in frames with horizontal drop-outs. - Not compatible with Centerlock or Boost hubs
Stan's NoTubes Neo RB End Caps
$20.00
Front 9mm QR SealLock end caps for Neo R road hubs. SealLock end caps feature a low-friction U-cup seal that snaps into place and stays secure even when your wheel is removed from your bike. Not compatible with disc brake hubs.
Robert Axle Project BOB Trailer Thru Axle
$62.00 - $69.00
Yes! A 12mm thru-axle adapter for BOB Trailers. These Robert Axles for BOB Trailers are specifically engineered to attach the proven BOB Trailer to your thru-axle-equipped bike. Take full advantage of your modern bike with 12mm thru-axles and harness the rigidity of the thru-axle to haul your BOB Trailer. Set out on any adventure, big or small. Great for off-road tours, trail building, hauling cargo, and more! - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The axle ends are stainless steel which allows for mounting of the BOB Trailer bobbins. - No special tools required. The design allows for wheel installation or removal using your standard 5mm hex wrench. - Please note: This axle does not come with the BOB Trailer bobbins (those are available separately). Or, you can reuse your bobbins from the stock BOB Trailer Quick Release that came with your trailer. - Designed, built, and quality tested in the USA. Proven around the world.
Robert Axle Project Front Lightning Bolt-On Thru Axle for Focus R.A.T. Bikes
$52.00
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer the highest quality, simple, lightweight alternative to that bulky handle. - This axle is compatible with bikes that have a Focus R.A.T. thru-axle in the fork with 100 x 12mm front hubs. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
Robert Axle Project Front Lightning Bolt-On Thru Axle
$42.00 - $48.00
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
Robert Axle Project RAP Bobbins
$18.50
These bobbins are made by the Robert Axle Project and are identical to the bobbins that came with your original BOB skewer. Slide them on your axle ends to complete your Robert Axle thru axle for BOB Trailer. - Sold in pairs - Manufactured from 303 Stainless Steel - Includes stainless steel hardware for attaching to axle
Cane Creek Helm D-Loc Thru-Axle
$55.00
Thru Axle for Helm suspension forks.
Stan's NoTubes Neo Durasync Freehub
$80.00 - $85.00
Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed. - 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration - Chromed steel bearings - Wide bearing stance and axle design reduces flex and adds durability - Low drag main seal prevents contamination and reduces resistance - Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components
Robert Axle Project Rear Lightning Bolt-On Thru Axle
$48.00
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
Wheels Manufacturing Inc. Freewheel/BB Spacer
$16.50
Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10
Wheels Manufacturing Inc. CN-R108 Cone
$10.00
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Rear 10mm x 1 axle - Shimano Rear Right Cone - Threads: 10mm x 1 - Diameter: 16.9mm - Length: 12.5mm - Cone Wrench Size: 15mm - 1 cone per bag COMPATIBLE HUBS: - Sora FH-3300, 9-spd Rear
Problem Solvers Stainless Downtube Shift Cable Adjusters
$24.99
The Problem Solvers Downtube Shift Cable Adjusters replace your existing shift adjusters, or let you add integrated shifters to your current down tube shifter-equipped road bike. Made from durable plastic and stainless steel, these adjusters are built to last for countless miles on your road steed.
SRAM X0 Hub Conversion Caps
$18.00 - $27.00
SRAM's X0 conversion caps are the ticket for converting your X0 hubs to a different axle type.
Robert Axle Project Trainer Thru Axle
$54.00
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
WTB TCS AL 34mm Presta Valve
$24.95
WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 34mm
WTB TCS AL 46mm Presta Valve
$25.95
WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 46mm
Wheels Manufacturing Inc. Outer Axle Nut
$1.25 - $5.75
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually
Wheels Manufacturing Inc. Axle-17
$36.00
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese front hubs - Type: Hollow Axle - Threads: 9mm x 1 - Diameter: 9mm - Length: 110mm - 1 axle per bag
Zipp Disc Wheel Valve Cover Patches
$6.00
A simple solution for completing the Zipp aerodynamic package by covering the valve access hole on most disc wheels. Black, self-adhesive oval patches with the Z logo, in a package of five.
Wheels Manufacturing Inc. Axle-10 Axle
$38.00
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs with 126mm spacing - Type: Hollow Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 137mm - 1 axle per bag
Page 1 of 9 Next page